ANCHOR

Resin-A GE-825 (Cartridge type)

Resin anchor (Injection System)

  • ■Used for a large number of installations by large capacity and exclusive air gun.
  • ■Can be used for various bolts, sizes and shapes of different reinforced steels.
  • ■Used extensively for concrete, brick, stone material and hollow base material.
  • ■Demonstrates stable fixing strength because primary material and hardening agent are constantly mixed by mixing nozzle.
  • ■Adopts a highly alkali resistant epoxy acrylate resin.

GE-825 series

Resin-A GE-825 (Cartridge type)

unika news PDF (1.1MB)

Uses

Concrete•Stone material•Hollow base material•ALC

Installation method

  1. Drill vertically to target surface with the determined preparation diameter and preparation hole depth.
  2. Use a dust collector or blower to thoroughly remove chips in the hole.
  3. Remove chips adhered in the hole using a brush, and use a dust collector or blower to clean in the hole again.
  4. Insert the nozzle down to the hole bottom and fill resin.
  5. Insert the bolt down to the hole bottom while slowly turning it by hand.
  6. Do not move the anchor bolt within the determined hardening time after embedding.

■Installation explanatory video

Resin-A GE-825 (Cartridge type) Installation explanatory video

Smart phone and a tablet is here.

■Uses

Foundation work for iron frame, Passage construction work, Tunnel construction work, Installation for vibrating machines.

■Installation specifications

Nominal
diameter(mm)		 M8 M10 M12 M16 M20 M22 M24
Preparation
hole
diameter(mm)		 10.0 12.0 14.0 18.0 24.0 25.0 28.0
Embedment
depth(mm)		 80 90 110 125 170 190 210
Required
resin
amount(ml)		 4 6 9 15 42 43 66
Recommended
tightening
torque(Nm)		 11 22 38 95 170 210 260
Number of pieces
installed(Pcs.)		 196 133 86 54 18 18 11

*Number of pieces installed is for reference number of pieces at a loss rate of 20%.

■Plastic sleeve installation specifications

Nominal
diameter(mm)		 M8 M10 M12
Preparation hole
diameter(mm)		 15.0 15.0 20.0
Matching
sleeve(Code)		 RA-P1585 RA-P1585 RA-P2085
Required resin
amount(ml)		 30 30 40

■Structural Drawing

Structural Drawing

■Installation Example

  • Continuous thread bolt

  • Plastic sleeve

■Shape of bolt used

Shape of bolt used

Cannot be used for a round bar. Use bolts which have irregularity on a surface such as a continuous thread bolt and different shape bar steel.

■Guideline for hardening time

Temperature(℃) -5 5 15 25 35
Use time(minutes) 40 20 9 5 3
Hardening time(minutes) 180 90 60 30 20

(Do not move the anchor reinforcement within the hardening time.)

Make sure to read before installation.

Precautions on use

  • Avoid direct sunlight and store in a well-ventilated place where the temperature does not rise so high.
    (Never raise the temperature above 40℃. Always keep the temperature in the range of 5 to 25℃.)
  • Do not bring close to fire or high temperature objects.
  • Cartridge can be stored until the expiration date for use under standard storage conditions.
  • Wear protective equipment (such as protective glasses and mask) when using.
  • When resin adheres to skin, irritation may occur in rare cases. Take action such as immediately wiping and rinsing with a hot soapy solution.
    In addition, if resin gets into eyes, immediately rinse with a large amount of water and seek medical attention.

Precautions on installation

  • Make sure to provide the drilling diameter and drilling depth as described in the specifications.
  • Make sure to use both a metallic brush and blower to sufficiently clean inside the hole.
  • Make sure to mount the mixing nozzle with it just before use.
  • Make sure to discard first approximately 10cc at a time of first use and nozzle replacement. (Mixing improperly may result in reduction in strength.)
  • This cannot be used for a steel bar with no irregularity such as a round bar.
  • Refer to the scale on the cartridge label for discharge resin amount.
  • Do not move the bar steel nor apply load within the determined hardening time.
GE type (Resin cartridge)
Size Capacity(ml) Content(Pc.) JAN Code
GE-825 825 GE-825 Cartridge*1 Mixing nozzle*2 4989270930308

GE type exclusive parts
Product name Size Matching cartridge JAN Code Appearance
Mixing nozzle(3 Pcs.) RA-MX3 GE 4989270930179
Air gun 825 RA-AGUN825 GE-825 4989270930346

*Used air pressure: 0.6~1MPa

■Related items

Push pump
Size Specifications JAN Code Appearance
RA-PUP (Nozzle diameter)
10mm
(Hose length)
270mm		 4989270930162
Metal brush
Size Specifications JAN Code Appearance
RA-MB10 Φ10*300 4989270930292
RA-MB13 Φ13*300 4989270930193
RA-MB18 Φ18*300 4989270930209
RA-MB28 Φ28*300 4989270930216
Extension nozzle(including three)
Size Specification JAN Code Appearance
RA-EXP3 Φ8×1m 4989270930445
Plastic sleeve (including 10 pieces)
Size Specifications JAN Code Appearance
RA-P1585 15*85(M8/10) 4989270930254
RA-P2085 20*85(M12) 4989270930261

Site Map

Copyright(C) 2012 UNIKA CO., LTD. All rights reserved.